Ratings & Reviews for Kobalt adjustable rolling table saw stand Steel Adjustable Rolling Table Saw Stand

Terrible stand

Poor quality, stand does not stay together, poor design

cheap junk

The lever to adjust the roller height snapped off with first use......it had been glued/epoxyed on, in tiny amounts. The fasteners for the legs (I bought 2 of these) would not remain tight with only very light use. The plastic caps covering the legs were too loose and kept falling off. I donated both of mine. This item is a piece of junk.

Bottom bracket will not tighten

Bad barrel nut in unit repeated emails with no results

Almost perfect

Works great i have two but with the second one they forgot to drill the holes for attaching the roller section to the base. It was easily fixed just annoying.

Questionable Design

This unit broke before I could ever use it. The height adjustment knob broke off due to a poor spot weld that held the adjustment screw. This was not the place to put a spot weld which was weak.

Broke on first use

This is cheap garbage. Setting it up for its first use and the nut that is welded onto the column to hold the support in place snapped off. It’s going right back

For years I always had my kids help hold or use buckets to hold the boards when making cuts. None of them really worked out great. Picked up a few of the Kobalt rolling stands and they work great! Quality isn't the best but for lite duty home projects it will be perfect. Lite weight and easy to set up. You will never want to cut long boards again with out one of these.

great buy

THese rollers work great for feed and outfeed for my table saw and chop saw. They are so inexpensive that i wish i had bought them years earlier

Poor quality.

I purchased three of these roller stands. Two had the height adjustment nut break within the first five minutes. The third had a manufacturing defect and was returned before any of them were used. Same issue as other negative reviews. You can tell they were not properly welded.

Handle broke

The first time I used it, the handle broke. The top section was still sliding so I tightened it just a little more. Snap! Unfortunately, I bought this a couple months ago. The box and, I’m sure, the receipt are long gone. I may try to drill a slot through it to put a cotter pin.

Just beought this product was settring it up for the height when the welds around the adjust handle nut broke so on my way back to lowes to return it if you get dont tighten it to hard. Welding needs to be better on the handle adujustment nut

Junk

I bought the first one in 2018, despite a number of negative reviews. It was holding ok, but I made sure I did not touch the adjustment handle. I needed a second one to support wide plywood sheets, went for it, and the handle broke while I assembled the stand. And I was gentle with it. It is going back to Lowe’s first thing tomorrow morning.

Failed before I even used it

I never even got a chance to use this stand before the handle that adjusts the height of the roller broke off. And the little barrel clamp that holds the feet on one of the legs kept failing and I had to tape it to the leg. Spend a few extra dollars and buy something better made. Is this typical of Kobalt quality

Useful, but fell apart on the first use

The nut tacked onto the main body popped off the first time I went to use it. Had to weld it back on to use it. Otherwise seems fine.

Handle nut not welded properly

For the most part, these seem okay, except that, as others have mentioned, the nut that the handle screws into breaks. It's a crappy weld, and it's made worse because when the handle screws in, it doesn't press directly against the tube that slides up and down. Instead, it has to bend a bit of metal which then contacts the tube and presses against it. There's some slop, so the handle actually gets tight before the sliding tube has any real pressure against it. You can reduce this slop by putting...

Adjustable table saw stand

Great piece to add to a portable table saw. Easy to use and a great help in ripping a long piece of wood.

Stand for table saw

Had to weld the nut on height adjustment! Wanted on it several weeks to get so i didn"t want to send it back!

Great product for the price

These were cheapest rolling stands I found, great product, easy to assemble, easy to collapse and store. Just a super convenient design to use, store and assemble. Only recommendation is to put lock tite on the bolt for the legs, then really tighten down. Seem to always get a little loose and have to retighten. But other wise great product would not hesitate to buy two more of these