Ratings & Reviews for Hillman 1/4-in x 20 Zinc-plated Steel Wood insert Nut 4 Count
Ratings may include incentivized customer reviews.
What Customers Are Saying
Customers report mixed results with these threaded inserts. Many describe the metal as too soft and prone to cracking or stripping during installation, particularly in hardwoods, with some finding the material non-magnetic and brittle. However, a substantial group confirms the inserts work well in soft woods, particle board, and MDF when pre-drilled correctly or combined with epoxy. Success depends heavily on application type and installation method. While some praise smooth threads and functionality, others cite poor value and lack of clear installation guidance. Overall, reviewers find them suitable for specific soft-wood projects but unreliable for demanding applications.
Customer review summary generated by AI, including incentivized reviews.Inserts
Would RecommendExcellent
From 1_SLASH_4-in x 20 Steel Cast zinc Wood insert Nut 4 Count Verified Purchaser
Easy to use.
From 1_SLASH_4-in x 20 Steel Cast zinc Wood insert Nut 4 Count Verified Purchaser
Not bad
Would Recommendthe deep well's, strips out very easy tho.
From 1_SLASH_4-in x 20 Steel Cast zinc Wood insert Nut 4 Count Verified Purchaser
Repair vintage chair leg.
I bought this to support a broken leg on my vintage chair. Hard part was getting the right replacement size and removing old piece.
From 1_SLASH_4-in x 20 Steel Cast zinc Wood insert Nut 4 Count Verified Purchaser
broke hex head off
Would Not Recommenddon't bother unless you are using particle board. very cheap. head will break. go easy.
DON'T BUY THIS CHEAP GARBAGE
Would Not RecommendIt's the most worthless grade of steel imaginable, it tears to pieces at the slightest tension and ruins your project. It's a scam manufacturer that Lowes should stop buying from.
Hello, We’re sorry to hear that this product was unsatisfactory and did not meet or perform to your expectations. We will continue to monitor product...
WEAK material
Would Not RecommendIt did the job ... barely. The material is SO weak! It's good that these came in a 4-pack because I broke 2 of them trying to screw them into the wood. You must oversize the hole so that it's not screwing in very much. Eventually, they did the job, but barely.
From 1_SLASH_4-in x 20 Steel Cast zinc Wood insert Nut 4 Count Verified Purchaser
Hello, We’re sorry to hear that this product was unsatisfactory and did not meet or perform to your expectations. We will continue to monitor product...
Works fine if you use your head.
Would RecommendYes, as others said, the 6mm drive on these will strip out pretty easily. However, there are other ways to set these inserts. When the first one went into the kiln dried Douglas fir, it stripped about half-way in. I didn't want to mangle it up trying to get it out, so plan B. I grabbed a two inch long 1/4-20 hex head bolt and a 1/4-20 nut. I installed the nut onto the bolt, then threaded the bolt into the insert. I then tightened the nut against the insert, used a 7/16 inch wrench on the bolt, a...
The person that makes these is not educated usable
It fits but it made wrong it will split the wood on insertion because of the wide ness at the top
Verified Purchaser
Hello, We’re sorry to hear that this product was unsatisfactory and did not meet or perform to your expectations. We will continue to monitor product...
Couldn't figure out how to uses them.
From 1_SLASH_4-in x 20 Steel Cast zinc Wood insert Nut 4 Count Verified Purchaser
This worked for us
Product was ok..just what we were looking for
From 1_SLASH_4-in x 20 Steel Cast zinc Wood insert Nut 4 Count Verified Purchaser
Hello, Thank you for providing us insight on your product experience. We apologize that the product did not perform to your expectations and we will ...