FREE SHIPPING ON QUALIFYING ORDERS $49 OR MORE
Keep your children engaged in simple, clean fun for hours by building them a sandbox. All you need is a little space, a weekend and some basic carpentry skills.
Product costs, availability and item numbers may vary online or by market.
Missing anything? Shop Online
The location of the sandbox is often determined by where you have space available. The eight-foot by eight-foot frame we're building takes up 64 sq. ft. You may be pleased to have less yard to mow, but if you can't spare the space, work with a smaller sandbox in the area that you have. The plans below can easily be re-sized to fit your space.
Sun or shade? Remember that a sandbox in full sun means the youngsters are exposed to UV rays. On the other hand, placement directly under a tree requires cutting tree roots when digging. At best this is a difficult task-it could also damage or kill the tree. Look for a spot that receives some shade from the house or from nearby trees. For safety's sake, locate the sandbox where you can keep an eye on the youngsters while they're playing.
When planning the size, make room for dump trucks, sand buckets and the neighbors' kids. Remember that you're going to have to put sand in it -- perhaps a lot of sand. The example we're using requires 32 cu. ft. of sand (about 64 fifty-pound bags). If this sounds like too much, you can easily reduce the dimensions. The bracing and corner assembly construction will be the same regardless of the length and width.
Which Material to Use?
Cedar is referenced in the materials list above, but not available everywhere. There are other suitable products you can use. Since many sandboxes will only be used a few years, hardwood or softwood boards may be use. Treated lumber is also an option, just make sure it's safe for use around humans, pets, plants, and vegetables.
When planning a location, remember your sandbox probably won't be a permanent fixture. When the kids outgrow it, convert the area back to lawn or a make a new flower bed.
When you've decided on site and size, measure, mark and prepare the area.
Step 1 - Use twine and stakes to make straight lines.
Step 2 - Cut out the shape with a shovel.
Step 3 - Remove sod (use it to cover bare spots in your yard if you have any).
Step 4 - Dig out the soil. You'll want the bottom edge of the sandbox slightly below the surface to help keep the walls in place.
Step 5 - Level the cleared area if necessary.
Step 6 - Put down a layer of landscape fabric (not plastic) to allow drainage and prevent weeds and grass from popping up through the sand.
To minimize cuts, we're building our sandbox from 8-ft lumber. Cedar is waterproof, attractive and approved for ground contact. To get the depth we need (12-in), the 6-in wide boards require joining.
Step 1 - Square and cut four of the 1 x 6 boards to 8-ft lengths.
Step 2 - Use construction adhesive to edge glue and clamp two sets of 8-ft boards. Allow the adhesive to cure according to the manufacturer's instructions. The glued 8-ft boards are sides A and C of the sandbox.
Step 3 - Cut eight 10-in pieces from one of the 1 x 3 boards. These are the inside supports.
Step 4 - Use 1 1/4-in galvanized screws to secure one inside support at each end of each glued 8 ft. board. The 10- in 1 bys should be on the inside face, flush with the ends of the 8-ft boards as shown in the picture.
Step 5 - Square and cut four of the 1 by boards to 7-ft 9-in lengths.
Step 6 - Use construction adhesive to edge glue and clamp two sets of 7-ft 9-in boards. Allow the adhesive to cure according to the manufacturer's instructions. The glued 7-ft 9-in boards are sides B and D of the sandbox.
Step 7 - Secure one inside support at each end of each glued 7-ft 9-in board (see Step 4).
Step 8 - Cut the remaining 1 by boards into 20-in lengths. You should have twelve 20-in 1 x 3s.
Step 9 - Cut one end of each 20-in 1 x 3 to a point (see diagram). The 20-in 1 bys will serve as stakes for the sides of the sandbox.
Step 10 - Finish all of the pieces.
Step 1 - Stand one of the 8-ft side-pieces on edge and butt the end of one of the 7-ft 9-in pieces to the inside support on the 8-ft piece. Drive 3-ft galvanized deck screws through the 8-in piece into the 7-ft 9-in piece. Do the same on opposite end of the 8-ft piece. Remember to keep the inside supports facing the inside of the sandbox.
Step 2 - Attach the second 8-ft piece to the 7-ft 9-in piece the same way as the first and square the sandbox. Secure the two halves together to complete the box.
Step 3 - Drive three stakes into the ground along the outside of each side of the sandbox. Position the first stake centered on the side-piece Position the other two stakes two feet to the left and right of the first. Drive each stake so its top is flush with the top edge of the side-piece.
Step 4 - Drive 1 1/4-in galvanized screws through the stakes into the side-pieces. The stakes help reinforce the sides of the sandbox and keep it square.
Step 5 - Sand lightly if needed to prevent splinters.
You'll need to know the volume of the box before buying sand.
Length x Width x Height = Volume
Example: For our box, 8 x 8 x 1= 64
The volume of the sandbox is therefore 64 cubic feet. Prepackaged, bagged sand is available. Usually called play sand, it's most likely washed river sand, which is smoother and cleaner than builder's sand. A fifty-pound bag is about one half of a cubic foot, so 64 bags should fill it about halfway. Leave room in the box for toy dump trucks, buckets, shovels and the kids. You can always buy a few more bags of sand to add if needed.
It's advisable to cover the sandbox when it's not in use. Cats are especially fond of sandboxes. Covers also keep moisture out while reducing leaves and other debris that make their way into the sand. The perfect homemade sandbox cover is perhaps yet to be invented, but here are some options:
Here is the completed sandbox. An alternate version in the main image above has two boards added for seating.