HTH Pool Balancing Chemicals

HTH   5-lb pH decreaser Pool Balancer

Use HTH 6-Way Test Strips or Test Kit to test your water weekly to make sure the pH level is between 7.2 and 7.8 ppm. If the pH measures above 7.8, add HTH pH Down directly to the pool water to decrease the pH. Swimming can resume immediately after treatment.

Pool Mate   7-lb Stabilizer Pool Balancer

Pool Mate Chlorine Stabilizer and Conditioner will cut chlorine loss caused by sunlight. Customers save money when they use Pool Mate Chlorine Stabilizer and Conditioner. If you use Pool Mate Chlorine Stabilizer and Conditioner you can cut chlorine consumption by up to 25%. Pool Mate Chlorine Stabilizer and Conditioner will help sustain ongoing chlorine residual. Add this product to your pool in the spring and you will improve chlorine effectiveness all season long. This product disperses rapidly to establish a chlorine protection quickly. It stabilizes pool water and extends the life of the disinfectant. Use a reliable test kit to determine the stabilizer concentration in the pool water. Follow the guide below to bring the pool water to the desired range of 40-100 ppm. If the pool is new, just refilled, or has no stabilizer; add 4 oz. of this product per 1000 gallons to give the desired 40-100 ppm. Add this product slowly into the skimmer, or if desired, premix in a pail of warm water and then add directly to the skimmer. Be sure the filter is clean. Recirculate the water continuously for 24 hours to dissolve completely. Always maintain the chlorine residual in your pool at 2.0-4.0 ppm and pH at 7.4-7.6. For 5,000 gallon pools, to increase 10ppm add 6.3 oz., to increase 20 ppm add 12.5 oz., to increase 30 ppm add 1.2 lbs., to increase 40ppm add 1.6 lbs., to increase 50ppm add 2.0 lbs. For 10,000 gallon pools, to increase 10ppm add 12.5 oz., to increase 20 ppm add 1.6 lbs., to increase 30 ppm add 2.3 lbs., to increase 40ppm add 3.1 lbs., to increase 50ppm add 3.9 lbs.. For 20,000 gallon pools, to increase 10ppm add 1.6 lbs., to increase 20 ppm add 3.1 lbs., to increase 30 ppm add 4.7 lbs., to increase 40ppm add 6.3 lbs., to increase 50ppm add 7.8 lbs.. Contains 100% Cyanuric Acid.

Pool Mate   25-lb Calcium hardness increaser Pool Balancer

Robelle Calcium Plus is used to raise calcium hardness levels when measures drop below the recommended range of 200-400 ppm. If calcium hardness levels are too low the soft water will corrode pool equipment, etch pool plaster and may cause metallic stains. This is a dry granular product that increases the total hardness in pool water to the recommended range.

HTH   4-lb Calcium hardness increaser Pool Balancer

Use HTH® 6-Way Test Strips or Test Kit to test your water weekly and make sure the calcium hardness level is between 200 and 500 ppm. If it falls below 200 ppm, add HTH® Calcium Hardness Up to raise calcium hardness level.

Pool Mate   25-lb Calcium hardness increaser Pool Balancer

Pool Mate Calcium Plus is used to raise calcium hardness levels when measures drop below the recommended range of 200-400 ppm. If calcium hardness levels are too low the "soft water" will corrode pool equipment, etch pool plaster and may cause metallic stains. This is a dry granular product that increases the total hardness in pool water to the recommended range. Directions for use: Test for calcium hardness with a reliable test kit.The desired range for calcium hardness is as follows: Vinyl Pools - 200-300 ppm. Tile and Exposed Aggregate Pools - 200-400 ppm. Marcite, Fiberglass or Painted Pools - 250-400 ppm. If the calcium hardness tests less than the desired range, add this product according to the guide below. Place this product into a plastic bucket already filled with swimming pool water. Do this in a ration of up to 2 pounds of product per approximate 5-gallon bucket of water. Slowly pour this solution around the perimeter of the swimming pool while the circulating system is operating. In a 10,000 gallon pool, do not add more than 10 pounds of this product per 2 hour period. For 5,000 gallon pool: to increase by 10 ppm add 7.2 oz., to increase by 20 ppm add 14.4 oz., to increase by 30 ppm add 1.35 lbs., to increase by 40 ppm add 1.8 lbs., to increase by 60 ppm add 2.7 lbs., to increase by 80 ppm add 3.6 lbs., to increase by 100 ppm add 4.5 lbs. For 10,000 gallon pool: to increase by 10 ppm add 14.4 oz., to increase by 20 ppm add 1.8 lbs., to increase by 30 ppm add 2.7 lbs., to increase by 40 ppm add 3.6 lbs., to increase by 60 ppm add 5.4 lbs., to increase by 80 ppm add 7.2 lbs., to increase by 100 ppm add 9 lbs. For 20,000 gallon pool: to increase by 10 ppm add 1.8 lbs., to increase by 20 ppm add 3.6 lbs., to increase by 30 ppm add 5.4 lbs., to increase by 40 ppm add 7.2 lbs., to increase by 60 ppm add 10.8 lbs., to increase by 80 ppm add 14.4 lbs., to increase by 100 ppm add 18 lbs. 100% Calcium Chloride Compound.

Pool Mate   16-lb Stabilizer Pool Balancer

Pool Mate Chlorine Stabilizer and Conditioner will cut chlorine loss caused by sunlight. Customers save money when they use Pool Mate Chlorine Stabilizer and Conditioner. If you use Pool Mate Chlorine Stabilizer and Conditioner you can cut chlorine consumption by up to 25%. Pool Mate Chlorine Stabilizer and Conditioner will help sustain ongoing chlorine residual. Add this product to your pool in the spring and you will improve chlorine effectiveness all season long. This product disperses rapidly to establish a chlorine protection quickly. It stabilizes pool water and extends the life of the disinfectant. Use a reliable test kit to determine the stabilizer concentration in the pool water. Follow the guide below to bring the pool water to the desired range of 40-100 ppm. If the pool is new, just refilled, or has no stabilizer; add 4 oz. of this product per 1000 gallons to give the desired 40-100 ppm. Add this product slowly into the skimmer, or if desired, premix in a pail of warm water and then add directly to the skimmer. Be sure the filter is clean. Recirculate the water continuously for 24 hours to dissolve completely. Always maintain the chlorine residual in your pool at 2.0-4.0 ppm and pH at 7.4-7.6. For 5,000 gallon pools, to increase 10ppm add 6.3 oz., to increase 20 ppm add 12.5 oz., to increase 30 ppm add 1.2 lbs., to increase 40ppm add 1.6 lbs., to increase 50ppm add 2.0 lbs. For 10,000 gallon pools, to increase 10ppm add 12.5 oz., to increase 20 ppm add 1.6 lbs., to increase 30 ppm add 2.3 lbs., to increase 40ppm add 3.1 lbs., to increase 50ppm add 3.9 lbs.. For 20,000 gallon pools, to increase 10ppm add 1.6 lbs., to increase 20 ppm add 3.1 lbs., to increase 30 ppm add 4.7 lbs., to increase 40ppm add 6.3 lbs., to increase 50ppm add 7.8 lbs.. Contains 100% Cyanuric Acid.

HTH   4-lb Stabilizer Pool Balancer

Use HTH® 6-Way Test Strips or Test Kit to test your water weekly. If the stabilizer level is below 20 ppm, apply HTH® Chlorine Stabilizer directly to the skimmer for healthy swimming

HTH   4-lb pH increaser Pool Balancer

Use HTH® 6-Way Test Strips or Test Kit to test your water weekly to make sure pH is between 7.2 and 7.8 ppm. If pH measures below 7.2, add HTH® pH Up directly to the pool water to raise the pH. Swimming can resume immediately after treatment.

Pool Mate   4-lb Stabilizer Pool Balancer

Pool Mate Chlorine Stabilizer and Conditioner will cut chlorine loss caused by sunlight. Customers save money when they use Pool Mate Chlorine Stabilizer and Conditioner. If you use Pool Mate Chlorine Stabilizer and Conditioner you can cut chlorine consumption by up to 25%. Pool Mate Chlorine Stabilizer and Conditioner will help sustain ongoing chlorine residual. Add this product to your pool in the spring and you will improve chlorine effectiveness all season long. This product disperses rapidly to establish a chlorine protection quickly. It stabilizes pool water and extends the life of the disinfectant. Use a reliable test kit to determine the stabilizer concentration in the pool water. Follow the guide below to bring the pool water to the desired range of 40-100 ppm. If the pool is new, just refilled, or has no stabilizer; add 4 oz. of this product per 1000 gallons to give the desired 40-100 ppm. Add this product slowly into the skimmer, or if desired, premix in a pail of warm water and then add directly to the skimmer. Be sure the filter is clean. Recirculate the water continuously for 24 hours to dissolve completely. Always maintain the chlorine residual in your pool at 2.0-4.0 ppm and pH at 7.4-7.6. For 5,000 gallon pools, to increase 10ppm add 6.3 oz., to increase 20 ppm add 12.5 oz., to increase 30 ppm add 1.2 lbs., to increase 40ppm add 1.6 lbs., to increase 50ppm add 2.0 lbs. For 10,000 gallon pools, to increase 10ppm add 12.5 oz., to increase 20 ppm add 1.6 lbs., to increase 30 ppm add 2.3 lbs., to increase 40ppm add 3.1 lbs., to increase 50ppm add 3.9 lbs.. For 20,000 gallon pools, to increase 10ppm add 1.6 lbs., to increase 20 ppm add 3.1 lbs., to increase 30 ppm add 4.7 lbs., to increase 40ppm add 6.3 lbs., to increase 50ppm add 7.8 lbs.. Contains 100% Cyanuric Acid.

Pool Mate   25-lb Alkalinity increaser Pool Balancer

Total Alkalinity Control is used when pH levels fluctuate widely over a short period of time. A low total alkaline reading is also indicative of corrosive pool water, a blue or green cast to the water and difficulty in holding chlorine residuals. Low alkalinity can cause equipment and plaster damage. If the alkalinity is too low or too high, the pH of the pool water will be difficult to maintain in the proper range. This product raises the total alkalinity in swimming pool water. It boosts the effectiveness of your pool water disinfectant, as well as aids in the prevention of scale formation, metal corrosion and the etching of pool surfaces. It helps maintain your pools pH level and eliminates pH bounce. Easy to use and dissolves quickly.

Pool Mate   5-lbs. pH increaser Pool Balancer

Test for pH with a reliable test kit. If the pH is low (7.2 or below) add this product according to the guide below. Pre-dissolve this product in a plastic pail and slowly pour around the perimeter of the swimming pool while the circulation system is operating. Allow system to operate for 1 hour after application. Retest the pH. If pH is still low, repeat this process until the pH reaches 7.4 to 7.6. How to increase pH for 5,000 Gallon Pool: base demand 1, add 2.6 oz., base demand 2 add 5.1 oz., base demand 3 add 7.7 oz., base demand 4 add 10.3 oz., base demand 5 add 12.8 oz., base demand 6 add 15.4 oz., base demand 7 add 1.1 lb. How to increase pH for 10,000 Gallon Pool: base demand 1, add 5.1 oz., base demand 2 add 10.3 oz., base demand 3 add 15.4 oz., base demand 4 add 1.3 lb., base demand 5 add 1.5 lb., base demand 6 add 1.9 lb., base demand 7 add 2.2 lb. How to increase pH for 20,000 Gallon Pool: base demand 1, add 10.3 oz., base demand 2 add 1.3 lb., base demand 3 add 1.9 lb., base demand 4 add 2.5 lb., base demand 5 add 3.2 lb., base demand 6 add 3.9 lb., base demand 7 add 4.5 lb.

Robelle   5-lbs. pH increaser Pool Balancer

Test for pH with a reliable test kit. If the pH is low (7.2 or below) add this product according to the guide below. Pre-dissolve this product in a plastic pail and slowly pour around the perimeter of the swimming pool while the circulation system is operating. Allow system to operate for 1 hour after application. Retest the pH. If pH is still low, repeat this process until the pH reaches 7.4 to 7.6. How to increase pH for 5,000 Gallon Pool: base demand 1, add 2.6 oz., base demand 2 add 5.1 oz., base demand 3 add 7.7 oz., base demand 4 add 10.3 oz., base demand 5 add 12.8 oz., base demand 6 add 15.4 oz., base demand 7 add 1.1 lb. How to increase pH for 10,000 Gallon Pool: base demand 1, add 5.1 oz., base demand 2 add 10.3 oz., base demand 3 add 15.4 oz., base demand 4 add 1.3 lb., base demand 5 add 1.5 lb., base demand 6 add 1.9 lb., base demand 7 add 2.2 lb. How to increase pH for 20,000 Gallon Pool: base demand 1, add 10.3 oz., base demand 2 add 1.3 lb., base demand 3 add 1.9 lb., base demand 4 add 2.5 lb., base demand 5 add 3.2 lb., base demand 6 add 3.9 lb., base demand 7 add 4.5 lb.

Robelle   10-lb pH increaser Pool Balancer

Test for pH with a reliable test kit. If the pH is low (7.2 or below) add this product according to the guide below. Pre-dissolve this product in a plastic pail and slowly pour around the perimeter of the swimming pool while the circulation system is operating. Allow system to operate for 1 hour after application. Retest the pH. If pH is still low, repeat this process until the pH reaches 7.4 to 7.6. How to increase pH for 5,000 Gallon Pool: base demand 1, add 2.6 oz., base demand 2 add 5.1 oz., base demand 3 add 7.7 oz., base demand 4 add 10.3 oz., base demand 5 add 12.8 oz., base demand 6 add 15.4 oz., base demand 7 add 1.1 lb. How to increase pH for 10,000 Gallon Pool: base demand 1, add 5.1 oz., base demand 2 add 10.3 oz., base demand 3 add 15.4 oz., base demand 4 add 1.3 lb., base demand 5 add 1.5 lb., base demand 6 add 1.9 lb., base demand 7 add 2.2 lb. How to increase pH for 20,000 Gallon Pool: base demand 1, add 10.3 oz., base demand 2 add 1.3 lb., base demand 3 add 1.9 lb., base demand 4 add 2.5 lb., base demand 5 add 3.2 lb., base demand 6 add 3.9 lb., base demand 7 add 4.5 lb.

Pool Mate   20-lb Alkalinity increaser Pool Balancer

Total Alkalinity Control is used when pH levels fluctuate widely over a short period of time. A low total alkaline reading is also indicative of corrosive pool water, a blue or green cast to the water and difficulty in holding chlorine residuals. Low alkalinity can cause equipment and plaster damage. If the alkalinity is too low or too high, the pH of the pool water will be difficult to maintain in the proper range. This product raises the total alkalinity in swimming pool water. It boosts the effectiveness of your pool water disinfectant, as well as aids in the prevention of scale formation, metal corrosion and the etching of pool surfaces. It helps maintain your pool’s pH level and eliminates pH “bounce”. Easy to use and dissolves quickly.

Robelle   5-lb Alkalinity increaser Pool Balancer

Total Alkalinity Control is used when pH levels fluctuate widely over a short period of time. A low total alkaline reading is also indicative of corrosive pool water, a blue or green cast to the water and difficulty in holding chlorine residuals. Low alkalinity can cause equipment and plaster damage. If the alkalinity is too low or too high, the pH of the pool water will be difficult to maintain in the proper range. This product raises the total alkalinity in swimming pool water. It boosts the effectiveness of your pool water disinfectant, as well as aids in the prevention of scale formation, metal corrosion and the etching of pool surfaces. It helps maintain your pools pH level and eliminates pH and bounce. Easy to use and dissolves quickly.

Pool Mate   25-lb Alkalinity increaser Pool Balancer

Total Alkalinity Control is used when pH levels fluctuate widely over a short period of time. A low total alkaline reading is also indicative of corrosive pool water, a blue or green cast to the water and difficulty in holding chlorine residuals. Low alkalinity can cause equipment and plaster damage. If the alkalinity is too low or too high, the pH of the pool water will be difficult to maintain in the proper range. This product raises the total alkalinity in swimming pool water. It boosts the effectiveness of your pool water disinfectant, as well as aids in the prevention of scale formation, metal corrosion and the etching of pool surfaces. It helps maintain your pools pH level and eliminates pH and bounce. Easy to use and dissolves quickly.

Pool Mate   50-lb Alkalinity increaser Pool Balancer

Total Alkalinity Control is used when pH levels fluctuate widely over a short period of time. A low total alkaline reading is also indicative of corrosive pool water, a blue or green cast to the water and difficulty in holding chlorine residuals. Low alkalinity can cause equipment and plaster damage. If the alkalinity is too low or too high, the pH of the pool water will be difficult to maintain in the proper range. This product raises the total alkalinity in swimming pool water. It boosts the effectiveness of your pool water disinfectant, as well as aids in the prevention of scale formation, metal corrosion and the etching of pool surfaces. It helps maintain your pools pH level and eliminates pH and bounce. Easy to use and dissolves quickly.