Flex Pipe Cut-Off Risers

Orbit   1/2-in MNPT x 1/2-in MNPT Flexible riser

The multi-flex riser allows you to go around obstacles between pipe and sprinkler heads. It has 1/2-inch male pipe thread (MPT) ends which connect from a PVC tee or elbow with a 1/2-inch Female outlet to a sprinkler head with 1/2-inch female inlet. For applications which require longer flexible risers, we recommend Blu-Lock pipe and fittings. For non-constant pressure outdoor irrigation use with cold water only.

Orbit   1/2-in MNPT x 1/2-in MNPT Cut-off riser

Before the introduction of swing pipe, the standard way to connect a sprinkler head to an underground lateral pipe was with a rigid PVC or cut-off riser. Cut-off risers are preferred over rigid PVC when it comes to replacement because a single size riser can be cut to fit a multitude of different sprinkler head heights. The threads are in 1-inch increment sections so you can easily cut off a section of threads to achieve the height you desire. The cut-off riser extension allows you to put two or more risers together to form even taller risers. The inlets and outlets are in 1/2-inch and 3/4-inch versions which are common for flush head, spray head and rotor sprinklers. They are made from durable, UV-resistant HDPE. For non-constant pressure outdoor irrigation use with cold water only.

Orbit   1/2-in MNPT x 1/2-in MNPT Cut-off riser

Riser pipes in rigid PVC allow you to connect from a sprinkler line, typically under the ground, to a hose faucet, drip manifold, shrub head, spray head, impact sprinkler, or gear-drive rotor. The wall thickness of PVC risers is thicker than Schedule 40 pipe which means it has greater rigidity and pressure rating. As plants grow you can extend the riser above the plants via addition of a coupling and another riser. Use a support stake to stabilize taller risers. When you no longer need a riser, you can simply thread a cap onto the end of it. Riser inlet/outlet sizes for residential applications are 1/2-inch, 3/4-inch, and 1-inch male pipe thread (MPT), with lengths spanning from just the pipe threads (“close nipple”) to 48 inches. Compatible with irrigation components from Orbit, Hydro-Rain, and other major brands. For outdoor irrigation use with cold water only.

Orbit   1/2-in MNPT x 1/2-in MNPT Flexible riser

The multi-flex riser allows you to go around obstacles between pipe and sprinkler heads. It has 1/2-inch male pipe thread (MPT) ends which connect from a PVC tee or elbow with a 1/2-inch Female outlet to a sprinkler head with 1/2-inch female inlet. For applications which require longer flexible risers, we recommend Blu-Lock pipe and fittings. For non-constant pressure outdoor irrigation use with cold water only.

Orbit   1/2-in MNPT x 1/2-in MNPT Cut-off riser

Riser pipes in rigid PVC allow you to connect from a sprinkler line, typically under the ground, to a hose faucet, drip manifold, shrub head, spray head, impact sprinkler, or gear-drive rotor. The wall thickness of PVC risers is thicker than Schedule 40 pipe which means it has greater rigidity and pressure rating. As plants grow you can extend the riser above the plants via addition of a coupling and another riser. Use a support stake to stabilize taller risers. When you no longer need a riser, you can simply thread a cap onto the end of it. Riser inlet/outlet sizes for residential applications are 1/2-inch, 3/4-inch, and 1-inch male pipe thread (MPT), with lengths spanning from just the pipe threads (“close nipple”) to 48 inches. Compatible with irrigation components from Orbit, Hydro-Rain, and other major brands. For outdoor irrigation use with cold water only.

Orbit   1/2-in MNPT x 1/2-in MNPT Cut-off riser

1/2 x 6, cut off riser, molded black high grade polyethylene construction, full ASTM standard threads, cut off from 1 to 6 segments.

Orbit   1/2-in MNPT x 1/2-in MNPT Cut-off riser 10 -Pack

This riser is made of flexible plastic composition that allows constant bending without breaking. It can be cut to the desired length and is not for use under continuous pressure.

Blazing   Barbed x 1/2-in FNPT Saddle Tee (Pack Of- 25)

The BLAZING saddle 1/2 in. FPT is for use with 3/4 in. polyethylene irrigation piping. This saddle is ideal for both contractors and DIY. The easiest way to a secure fit without any tools. Simply clamp, push down, twist, and you are done.

King Innovation   Barbed x 1/2-in FNPT Saddle Tee (Pack Of- 25)

The Blazing Saddle 1/2 FPT is for use with 1 in. PVC irrigation piping. This saddle is ideal for both contractors and DIY. The easiest way to a secure fit without any tools. Simply clamp, push down, twist, and you are done.

King Innovation   Barbed x 1/2-in FNPT Saddle Tee (Pack Of- 25)

The Blazing Saddle 1/2 FPT is for use with 1 in. polyethylene irrigation piping. This saddle is ideal for both contractors and DIY. The easiest way to a secure fit without any tools. Simply clamp, push down, twist, and you are done.

Blazing   Barbed x 1/2-in FNPT Saddle Tee (Pack Of- 25)

The BLAZING saddle 1/2 In. FPT is for use with 1-1/4 In. PVC irrigation piping. This saddle is ideal for both contractors and DIY. The easiest way to a secure fit without any tools. Simply clamp, push down, twist, and you are done.

Blazing   Barbed x 1/2-in FNPT Saddle Tee (Pack Of- 25)

The Blazing Saddle 1/2 in. FPT is for use with 1-1/4 in. polyethylene irrigation piping. This saddle is ideal for both contractors and DIY. The easiest way to a secure fit without any tools. Simply clamp, push down, twist, and you are done.

Blazing   Barbed X Barbed Saddle Tee (Pack Of- 25)

The BLAZING saddle swing pipe barb is for use with 1-1/4 In. PVC irrigation piping. This saddle is ideal for both contractors and DIY. The easiest way to a secure fit without any tools. Simply clamp, push down, twist, and you are done.

Blazing   Barbed x barbed Saddle tee 25 -Pack

The Blazing Saddle Swing Pipe Barb is for use with 1-in polyethylene irrigation piping. This saddle is ideal for both contractors and DIY. The easiest way to a secure fit without any tools. Simply clamp, push down, twist, and you are done.