SUNCOURT Duct Fans

RadonAway   9.7-in dia 166 CFM Plastic Centrifugal radon mitigation fan

The RadonAway RP145c radon fan is intended for use as a component of an active system for reducing radon. The RadonAway RP145c radon fan offers higher air flow, energy efficiency and quiet operation. It is ideal for both new construction and retrofit radon systems with a slab or membrane size of up to 2500 square feet. This fan is designed for moderate to good air flow, working most effectively with sub slab or sub-material conditions ranging from about 4 inches of clean, size 4-6 gravel to very loose soil. The RadonAway RP145c radon fan is built to resist moisture and can be mounted inside or outside on a 3 inch or 4 inch schedule 40 PVC vent pipe using 3 inch x 4 inch or 4 inch x 4 inch flexible couplings. When installing an active system for radon reduction, openings, major cracks and penetrations in the building slab or membrane must be sealed. Fan sizing for retrofit may require professional diagnostics and design.

SUNCOURT   6-in dia 250 CFM Galvanized steel Axial duct fan

Suncourt’s corded in-line duct fans provide a simple solution to boost air to a room that is too hot or too cold. This fan requires no electrical wiring; just plug the duct fan into the Suncourt duct stat temperature sensitive switch, sold separately, to eliminate the need of hard wiring to the furnace.

SUNCOURT   4-in dia 80 CFM Galvanized steel Axial duct fan

Suncourt’s corded in-line duct fans provide a simple solution to boost air to a room that is too hot or too cold. This fan requires no electrical wiring; just plug the duct fan into the Suncourt duct stat temperature sensitive switch, sold separately, to eliminate the need of hard wiring to the furnace.

RadonAway   12.5-in dia 66 CFM Plastic Axial radon mitigation fan

The RadonAway GP series radon fans, intended for use as a component of an active system for reducing radon, provide versatility and a broad performance range focusing on drawing pressure in moderate to tight soils when less air movement is necessary. They are ideal for use when multiple suction points are necessary. The RadonAway GP501c radon fan is suitable for new construction and retrofit systems and for existing fan replacement. It can be mounted inside or outside on 3 inch or 4 inch schedule 40 PVC pipe using 3 inch x 3 inch or 3 inch x 4 inch flexible couplings. When installing a system for radon reduction, any openings, major cracks and penetrations in the building membrane must be sealed. Fan sizing for retrofit may require professional diagnostics and design.

SUNCOURT   8-in dia 500 CFM Galvanized steel Axial duct fan

Suncourt’s corded in-line duct fans provide a simple solution to boost air to a room that is too hot or too cold. This fan requires no electrical wiring; just plug the duct fan into the Suncourt duct stat temperature sensitive switch, sold separately, to eliminate the need of hard wiring to the furnace.

Festa AMG Radon Fans   4-in dia 260 CFM Glass-reinforced poly resin Centrifugal radon mitigation fan

All Festa AMG Radon Fans are designed specifically for radon mitigation, utilizing the highest quality parts available. All Festa AMG models are made with compression molded housings, European engineered motorized impellers, and convenient installation features to ensure our fans are equipped for any ASD system. The Festa AMG Maverick radon fan is our most popular fan and fits 4" Fernco Couplers. We recommend the Festa AMG Maverick for moderate-sized, newer homes or structures ranging between 500- 2200 sq. ft. with porous sub-slabs such as gravel. The AMG Maverick is RF1 and RF2 suitable for radon resistant new construction.

AC Infinity   4-in dia 205 CFM Galvanized steel Centrifugal duct fan

The new Cloudline series contains a cutting-edge electronically commutated (EC) motor, controlled using precise electronic pulses and smart programming. This enables the inline fan to operate considerably quieter and reach low speeds without generating noise or heat. The EC motor is also twice as energy-efficient and can save up to 40% in energy costs, paying for itself in the long run.

RadonAway   11.75-in dia 334 CFM Plastic Centrifugal radon mitigation fan

The RadonAway RP265c radon fan is intended for use as a component of an active system for reducing radon. It has a 6 inch duct and is chosen most often by radon professionals when there is a need for quiet efficiency coupled with higher air flow. The RadonAway RP265 is ideal for retrofit systems and is best used with sub-slab or sub-membrane materials consist of about 4 inches of clean, size 4-6 gravel or loose to moderately loose soil. The RadonAway RP265c is built to resist moisture and can be mounted on a 4 inch schedule 40 PVC vent pipe using 4 inch x 6 inch flexible couplings. It can be used for building slabs or membranes 2500 plus square feet. When installing a system for radon reduction, openings, major cracks and penetrations in the building slab or membrane must be sealed. Fan sizing for retrofit may require professional diagnostics and design.

RadonAway   9.7-in dia 135 CFM Plastic Centrifugal radon mitigation fan

The energy star® rated RadonAway RP140c radon fan is intended for use as a component of an active system for reducing radon. The RadonAway RP140c is ideal for installation during new construction and renovations, providing superior performance and ultra-quiet, energy-efficient radon reduction. Designed for lower pressure and average flow, the RadonAway RP140c fan provides an especially efficient choice for very porous sub-slab/sub-membrane material (that is 4 inches of clean, size 4-6 gravel) and can be used for slab/membrane sizes up to 1600 square feet. The RadonAway RP140c is built to resist moisture and can be mounted inside or outside on a 4 inch schedule 40 PVC vent pipe using 4 in. x 4 in. flexible couplings. When installing a system for radon reduction, openings, major cracks and penetrations in the building slab or membrane must be sealed. Fan sizing for retrofit may require professional diagnostics and design.

HomeAire   4-in dia 70-CFM Galvanized Steel Axial Duct Fan

The HomeAire 4 inch duct boost fan is designed to give an old heating and cooling system the lift necessary to push conditioned air into existing or newly expanded living or working areas as well as any other areas where it is needed. They improve system efficiency and provide better energy efficiency.

AC Infinity   6-in dia 402 CFM Galvanized steel Centrifugal duct fan

The new CLOUDLINE series contains a cutting-edge Electronically Commutated (EC) motor, controlled using precise electronic pulses and smart programming. This enables the inline fan to operate considerably quieter and reach low speeds without generating noise or heat. The EC motor is also twice as energy-efficient and can save up to 40% in energy costs, paying for itself in the long run.

AC Infinity   6-in dia 402 CFM Galvanized steel Centrifugal duct fan

The new CLOUDLINE series contains a cutting-edge Electronically Commutated (EC) motor, controlled using precise electronic pulses and smart programming. This enables the inline fan to operate considerably quieter and reach low speeds without generating noise or heat. The EC motor is also twice as energy-efficient and can save up to 40% in energy costs, paying for itself in the long run.

SUNCOURT   12-in dia 800 CFM Galvanized steel Axial duct fan

Suncourt's corded in-line duct fans provide a simple solution to boost air to a room that is too hot or too cold. This fan requires no electrical wiring; just plug the duct fan into the Suncourt duct stat temperature sensitive switch, sold separately, to eliminate the need of hard wiring to the furnace.

SUNCOURT   10-in dia 650 CFM Galvanized steel Axial duct fan

Suncourt's corded in-line duct fans provide a simple solution to boost air to a room that is too hot or too cold. This fan requires no electrical wiring; just plug the duct fan into the Suncourt duct stat temperature sensitive switch, sold separately, to eliminate the need of hard wiring to the furnace.

RadonAway   4-in dia 126 CFM Plastic Centrifugal radon mitigation fan

The RadonAway XP201c radon fan is ideal for most standard radon mitigation jobs and is intended for use as a component of an active system for reducing radon. The XP201c’s unique motor and impeller design makes it one of the most durable general purpose radon mitigation fans on the market. This fan is a good choice for retrofit systems when the sub-slab/sub-membrane material consists of about 4 inches of clean, size 4-6 gravel or moderately loose to moderately tight soil and can be used for slab/membrane sizes up to 1600 sq. Ft. The slim, compact, moisture-resistant XP201 has a 4-inch duct and can be mounted inside or outside on a 3-inch or 4-inch schedule 40 PVC vent pipe using 4-inch x 4-inch flexible couplings. When installing a system for radon reduction, openings, major cracks and penetrations in the building slab or membrane must be sealed. Fan sizing for retrofit may require professional diagnostics and design.

SUNCOURT   6-in dia 180 CFM Galvanized steel Axial duct fan

Suncourt's in-line duct fans solve air delivery problems without major system rework or expense. They are engineered to overcome back pressure and boost air in forced air heating and cooling systems without upsetting the balance in the closed loop system.

HomeAire   8-in dia 210-CFM Galvanized Steel Axial Duct Fan

The HomeAire 8 inch duct boost fan is designed to give an old heating and cooling system the lift necessary to push conditioned air into existing or newly expanded living or working areas as well as any other areas where it is needed. They improve system efficiency and provide better energy efficiency.

AC Infinity   8-in dia 807 CFM Galvanized steel Centrifugal duct fan

The new CLOUDLINE series contains a cutting-edge Electronically Commutated (EC) motor, controlled using precise electronic pulses and smart programming. This enables the inline fan to operate considerably quieter and reach low speeds without generating noise or heat. The EC motor is also twice as energy-efficient and can save up to 40% in energy costs, paying for itself in the long run.

Festa AMG Radon Fans   3-in dia 221 CFM Glass-reinforced poly resin Centrifugal radon mitigation fan

All Festa AMG Radon Fans are designed specifically for radon mitigation, utilizing the highest quality parts available. All Festa AMG models are made with compression molded housings, European engineered motorized impellers, and convenient installation features to ensure our fans are equipped for any ASD system. The AMG Prowler offers more suction than the Maverick and fits 3” Fernco couplers. We recommend this fan for homes or structures between 500-2500 sq. ft. with semi-porous sub-slabs such as gravel and/or clay. The AMG Prowler is RF2 suitable for radon resistant new construction.

AC Infinity   8-in dia 807 CFM Galvanized steel Centrifugal duct fan

The new CLOUDLINE series contains a cutting-edge Electronically Commutated (EC) motor, controlled using precise electronic pulses and smart programming. This enables the inline fan to operate considerably quieter and reach low speeds without generating noise or heat. The EC motor is also twice as energy-efficient and can save up to 40% in energy costs, paying for itself in the long run.