Hot Tub & Spa Chemicals

MAV AquaDoc   16 Ounce(s) Low Odor Spa Seal Leak Spa

Have a leak in your hot tub but can't find it? AquaDoc's advanced leak sealer formula helps to fix minor hot tub leaks and cracks. Our professional grade leak sealer can seek out the hardest to find crack in your spa or hot tub to help stop leaks in their tracks. Our hot tub leak repair formula helps repair minor scratches, cracks, and leaks in your hot tub. Our leak sealer stops leaks fast! Seal your minor leaks and cracks within just 24 hours. There's no need to drain your hot tub. Simply add the spa leak sealer to the water in the area of the suspected leak. If you're unsure where the leak is, simply add to the water evenly. of AquaDoc's hot tub chemicals are proudly made in the USA. Directions for leak sealer usage:first, turn your hot tub pump off. Next, remove your cartridge or filter grids to avoid the product from going past the filtration system. If you have identified the leak, simply pour the recommended dosage directly into the water at the area of the leak. If the leak is unidentified, pour the recommended dosage to into the skimmer or spread throughout. Wait 30 minutes after application, then turn pump on and run the pump for 8 hours. After 8 hours, check spa to see if it is still losing water. If it's still losing water, apply a second application within the next 24 hours. Then, replace filter grids or cartridges after 24 hours and resume normal filtration. Wait at least 24 hours before anyone enters the hot tub.

Spa Choice   1 Piece count Spa Chlorine

Spa Choice Sanitizing Granules are designed to dissolve quickly and completely. Chlorine granules provide a steady source of available chlorine to spa water to control algae growth, kill bacteria and destroy organic contaminants. Spa choice chlorine granules are stabilized to protect against ultraviolet radiation from the sun, increasing the life of your chlorine. This product is designed to dissolve quickly and completely providing a steady source of available chlorine to control the growth of algae, kill bacteria and destroy organic contaminants. DIRECTIONS FOR APPLICATION: Broadcast the product evenly over a wide area in the deepest part of the spa with water circulating. DIRECTIONS FOR SPA AND HOT TUB USE: Each level teaspoon (0.17 ounces) of this product will provide approximately 1.4 ppm available chlorine in 500 gallons of water. Using an appropriate test kit, test and adjust the water to the following values: pH 7.2-7.8, total alkalinity 60-100 ppm, calcium hardness 200 ppm minimum. Maintain these conditions for proper spa and hot tub operation by frequent testing with a test kit. Do not allow cyanuric acid level to exceed 150 ppm. It is recommended that spas and hot tubs be drained every 30-90 days. More often under heavy use. Consult manufacturer’s recommendations concerning the compatibility of chlorine sanitizers with their equipment. Some oils, lotions, fragrances and cleaners may cause foaming or cloudy water and may react with chlorine sanitizers to reduce their efficacy. DIRECTIONS FOR START-UP (FRESHLY FILLED) 1. Turn on the circulation system and ensure that it is operating properly. 2. Add 6 teaspoons of this product for each 500 gallons of water. Check the free available chlorine (FAC) and, if below 4-5 ppm, repeat as needed. Re-entry into treated spas is prohibited above levels of 3 ppm of chlorine. DIRECTIONS FOR REGULAR USE: Turn on the circulation system and ensure that it is operating properly. Scatter approximately 3 teaspoons per 500 gallons of this product over the surface of water. Always use a clean dry spoon. Test for FAC and add additional product, if necessary, to attain 4-5 ppm FAC. Maintain 1-3 ppm FAC while the spa or hot tub is in use. After each use, shock treat with 9 teaspoons per 500 gallons water to control odors and algae. Repeat as needed. Re-entry into treated spas is prohibited above levels of 3 ppm of chlorine.

Clorox Pool&Spa   32 Ounce(s) Low Odor Spa Clarifier

Clorox Spa® System Cleanse attacks the root cause of most spa maintenance problems, the build-up of non-living organic waste contamination. Oils, lotions, cosmetics, hair products, and other non-living organics build up in spa water to produce cloudiness, unpleasant odors, and foaming. These contaminants collect and build up in spa circulation systems and filters. By purging the spa plumbing, you can improve water clarity and reduce the time and effort needed to maintain your spa.

HTH   16 Ounce(s) Low Odor Spa and Hot Tub Chemical Filter Cleaner Spa Filter cleaner

Remove cartridge(s) from your spa filter and hose off with water to remove loose debris. Fill a clean plastic container, bucket, pail or garbage can with 4 gallons of water. Empty the contents of the HTH Filter Cleaner bottle into the water to create the cleaning solution. Place the cartridge(s) upright in the solution and soak for 3 to 6 hours or overnight. Remove cartridges(s) from the solution, hose off and replace in your spa filter.

Spa Choice   2 Piece count Spa Bromine

Spa Choice Bromine Tabs fit in most spa feeders and floaters to continuously sanitize your spa or hot tub. Bromine is a powerful and effective sanitizer like chlorine, but it is odorless and less irritating to your skin and eyes. Spa Choice bromine tabs are "pre-stabilized," so your water is silky smooth without using a stabilizer or conditioner. DIRECTIONS FOR USE: Keep pH between 7.2-7.6 and never allow it to fall below 7.0. The treatment necessary for your pool or spa will change considerably depending upon those factors that burden the disinfection system. Some of the factors that will vary the required treatment are water temperature, bather load, exposure to windblown debris, thunder, rain storms, and length of filtration cycle. Users must wear chemical-resistant gloves while placing the tablet in the spas. FOR USE IN SPAS AND HOT TUBS: Before initially using this product in your spa or hot tub you will need to add 1/2 oz. of sodium bromide for each 100 gallons of water. The same treatment must be followed each time you drain and refill your spa or hot tub with fresh water. Introduce 3 tablets per 300 gallons of spa water with the use of a floating tablet feeder or automatic brominator installed on the spa equipment. Adjust tablet feeder or brominator to obtain an active bromine residual of at least 2 ppm. Maintain spa by adding 3 tablets per 300 gallons every 5-7 days or as needed to maintain an active bromine residual of 2 ppm at all times. Spa water has a tendency to foam and cloud; this is directly proportional to the amount of spa use. Cloudiness is due to the accumulation of body fats, oils and contaminants too small for the filtration equipment to remove, and is linked to rapid escalation of total dissolved solids in the water. To a great extent, defoamers, clarifiers, as well as shock treatments, demineralizers, or sequestering agents can be used to clear the water. When water clarification cannot be achieved, drain, clean, and refill the spa.

Spa Choice   2 Piece count Spa Bromine

Spa Choice Bromine Tabs fit in most spa feeders and floaters to continuously sanitize your spa or hot tub. Bromine is a powerful and effective sanitizer like chlorine, but it is odorless and less irritating to your skin and eyes. Spa Choice bromine tabs are "pre-stabilized," so your water is silky smooth without using a stabilizer or conditioner. DIRECTIONS FOR USE: Keep pH between 7.2-7.6 and never allow it to fall below 7.0. The treatment necessary for your pool or spa will change considerably depending upon those factors that burden the disinfection system. Some of the factors that will vary the required treatment are water temperature, bather load, exposure to windblown debris, thunder, rain storms, and length of filtration cycle. Users must wear chemical-resistant gloves while placing the tablet in the spas. FOR USE IN SPAS AND HOT TUBS: Before initially using this product in your spa or hot tub you will need to add 1/2 oz. of sodium bromide for each 100 gallons of water. The same treatment must be followed each time you drain and refill your spa or hot tub with fresh water. Introduce 3 tablets per 300 gallons of spa water with the use of a floating tablet feeder or automatic brominator installed on the spa equipment. Adjust tablet feeder or brominator to obtain an active bromine residual of at least 2 ppm. Maintain spa by adding 3 tablets per 300 gallons every 5-7 days or as needed to maintain an active bromine residual of 2 ppm at all times. Spa water has a tendency to foam and cloud; this is directly proportional to the amount of spa use. Cloudiness is due to the accumulation of body fats, oils and contaminants too small for the filtration equipment to remove, and is linked to rapid escalation of total dissolved solids in the water. To a great extent, defoamers, clarifiers, as well as shock treatments, demineralizers, or sequestering agents can be used to clear the water. When water clarification cannot be achieved, drain, clean, and refill the spa.

HTH   16 Ounce(s) Low Odor Spa and Hot Tub Chemical Clarifier Spa Clarifier

How to Use: Before treatment, check your spa filter and make sure it is clean. For best results, use HTH® Spa Filter Cleaner to clean a dirty filter. Turn the spa circulation system on and run continuously during treatment to ensure proper mixing and filtration. Shake the bottle before applying the clarifier to your spa water. Refer to on-pack instructions for proper dosage.

Spa Choice   2 Piece count Spa Chlorine

Spa Choice Sanitizing Granules are designed to dissolve quickly and completely. Chlorine granules provide a steady source of available chlorine to spa water to control algae growth, kill bacteria and destroy organic contaminants. Spa choice chlorine granules are stabilized to protect against ultraviolet radiation from the sun, increasing the life of your chlorine. This product is designed to dissolve quickly and completely providing a steady source of available chlorine to control the growth of algae, kill bacteria and destroy organic contaminants. DIRECTIONS FOR APPLICATION: Broadcast the product evenly over a wide area in the deepest part of the spa with water circulating. DIRECTIONS FOR SPA AND HOT TUB USE: Each level teaspoon (0.17 ounces) of this product will provide approximately 1.4 ppm available chlorine in 500 gallons of water. Using an appropriate test kit, test and adjust the water to the following values: pH 7.2-7.8, total alkalinity 60-100 ppm, calcium hardness 200 ppm minimum. Maintain these conditions for proper spa and hot tub operation by frequent testing with a test kit. Do not allow cyanuric acid level to exceed 150 ppm. It is recommended that spas and hot tubs be drained every 30-90 days. More often under heavy use. Consult manufacturer’s recommendations concerning the compatibility of chlorine sanitizers with their equipment. Some oils, lotions, fragrances and cleaners may cause foaming or cloudy water and may react with chlorine sanitizers to reduce their efficacy. DIRECTIONS FOR START-UP (FRESHLY FILLED) 1. Turn on the circulation system and ensure that it is operating properly. 2. Add 6 teaspoons of this product for each 500 gallons of water. Check the free available chlorine (FAC) and, if below 4-5 ppm, repeat as needed. Re-entry into treated spas is prohibited above levels of 3 ppm of chlorine. DIRECTIONS FOR REGULAR USE: Turn on the circulation system and ensure that it is operating properly. Scatter approximately 3 teaspoons per 500 gallons of this product over the surface of water. Always use a clean dry spoon. Test for FAC and add additional product, if necessary, to attain 4-5 ppm FAC. Maintain 1-3 ppm FAC while the spa or hot tub is in use. After each use, shock treat with 9 teaspoons per 500 gallons water to control odors and algae. Repeat as needed. Re-entry into treated spas is prohibited above levels of 3 ppm of chlorine.

HTH   2 Pound(s) Low Odor Spa and Hot Tub Chemical pH Up Spa Balancer

Use HTH Spa Test Strips to test your spa water. If pH measures below 7.2 ppm, add HTH Spa pH Up directly to the filter skimmer with the spa circulation system running. Refer to the on-pack chart for the correct dosage. After the spa circulation system has been running for 30 minutes, re-test pH and add more pH Up if necessary. Test and balance your spa water twice a week to maintain pH levels between 7.2 and 7.8 ppm

HTH   2.5 Pound(s) Low Odor Spa and Hot Tub Chemical pH Down Spa Balancer

How to Use: Use HTH® Spa Test Strips to test your spa water. If pH measures above 7.8 ppm, add HTH® Spa pH Down directly to the filter skimmer with the spa circulation system running. After the spa circulation system has been running for 30 minutes, re-test pH and add more pH Down if necessary. Test and balance your spa water twice a week to maintain pH levels between 7.2 and 7.8 ppm.

Clorox Spa   16-oz Spa Balancer

Clorox Spa pH Protect helps maintain a comfortable, stable pH level. This easy, one-step treatment softens spa water and makes balancing the water simple. For use in spas and hot tubs.

Spa Choice   5 Piece count Spa Bromine

Spa Choice Bromine Tabs fit in most spa feeders and floaters to continuously sanitize your spa or hot tub. Bromine is a powerful and effective sanitizer like chlorine, but it is odorless and less irritating to your skin and eyes. Spa Choice bromine tabs are "pre-stabilized," so your water is silky smooth without using a stabilizer or conditioner. DIRECTIONS FOR USE: Keep pH between 7.2-7.6 and never allow it to fall below 7.0. The treatment necessary for your pool or spa will change considerably depending upon those factors that burden the disinfection system. Some of the factors that will vary the required treatment are water temperature, bather load, exposure to windblown debris, thunder, rain storms, and length of filtration cycle. Users must wear chemical-resistant gloves while placing the tablet in the spas. FOR USE IN SPAS AND HOT TUBS: Before initially using this product in your spa or hot tub you will need to add 1/2 oz. of sodium bromide for each 100 gallons of water. The same treatment must be followed each time you drain and refill your spa or hot tub with fresh water. Introduce 3 tablets per 300 gallons of spa water with the use of a floating tablet feeder or automatic brominator installed on the spa equipment. Adjust tablet feeder or brominator to obtain an active bromine residual of at least 2 ppm. Maintain spa by adding 3 tablets per 300 gallons every 5-7 days or as needed to maintain an active bromine residual of 2 ppm at all times. Spa water has a tendency to foam and cloud; this is directly proportional to the amount of spa use. Cloudiness is due to the accumulation of body fats, oils and contaminants too small for the filtration equipment to remove, and is linked to rapid escalation of total dissolved solids in the water. To a great extent, defoamers, clarifiers, as well as shock treatments, demineralizers, or sequestering agents can be used to clear the water. When water clarification cannot be achieved, drain, clean, and refill the spa.

Leisure Time Products   2 Ounce(s) Spa Balancer

Leisure Time Alkalinity Increaser is formulated to raise total alkalinity safely and effectively. The concentrated granular formula allows gradual water balancing.

HTH   2 Pound(s) Low Odor Spa and Hot Tub Chemical Sanitizer Spa Bromine

Brominating Tablets will disinfect spa and hot tub water, keeping it clean, clear and free of odor. Brominating Tablets give the effectiveness of chlorine without the chlorine odor. Proper sanitary practices require changing spa water at a minimum of every 30 days.

MAV AquaDoc   2 Piece count Spa Clarifier

The hot tub clarifier chemical that works. Eliminate cloudy water, extend your hot tub filter life, and keep your pH balanced with our spa water clarifier. Restore hot tub water clarity with the best spa clarifier for hot tubs. AquaDoc's hot tub clarifier helps fix cloudy water, excessive foaming, pH imbalance, and prevents long lasting stains. If your water is balanced and it still isn't clear, you likely need our hot tub clarifier to get you crystal clear water. Why is our spa clarifier so amazing. AquaDoc's spa clarifier attracts micro dirt particles together, almost like a magnet, so that they can be caught by the hot tub filter. This clarifies your hot tub and extends your spa filter cartridge lifespan. Our hot tub clarifier is extremely easy to use. Simply add 2oz of our premium water clarifier for every 250 gallons of water while the blower, or hot tub jets, are on, turn on the filtration system until the water is clean and clear. Use 2 times per week for regular hot tub maintenance. All of AquaDoc's hot tub chemicals are professional grade, top quality products that are made in the USA. Directions for clarifier usage: we recommend using AquaDoc's hot tub filter cleaner to ensure filter cartridge is clean before use. Then, turn circulation system on and leave on throughout use. This ensure proper mixing of the spa water clarifier. Next, shake bottle of water clarifier to mix up the professional grade spa chemical. Add 2 fl oz of mac AquaDoc's water clarifier chemical for every 250 gallons of water. Continue running hot tub circulation system until water is crystal clear. For regular maintenance, add 2 fl oz of spa clarifier for every 250 gallons 2x a week.

MAV AquaDoc   12 Piece-Count Spa

Calcium levels low? The ideal hardness level is 200 - 400ppm (parts per million). Proper calcium levels in your hot tub make managing pool chemistry significantly easier and cost effective. It makes your water balance more predictable and therefore easier to manage - resulting in less chemical waste. Increase spa water hardness with our spa calcium increaser for hot tubs. Avoid corrosion from soft water with our premium calcium hardness increaser. Low calcium levels can cause corrosive water which can ruin your spa or hot tub. to prevent etching and staining at your tub's surface level that can be caused from low calcium levels. Balance your water easily and effectively using our spa hardness increaser. Directions for spa calcium balancing: first, check your hot tub's hardness levels to determine if calcium levels are too low (they should be between 200 - 400ppm). Adding 1 ounce of AquaDoc's calcium increaser will increase 500 gallons of water's hardness level by 10ppm. After determining hardness level goal, pour product into spa. Please note, the equipment must be on while adding calcium increaser. Run filter for 1 - 2 hours, wait 20 minutes, then re-test water. It's always better to underdone at first and measure before adding more.

MAV AquaDoc   16 Ounce(s) Spa Stablizer

Have scum line stains or smelly water? Our natural enzyme chemical is here to help. Hot tubs are more gross than we think - hot tubs naturally collect body oils, suntan lotion, and cosmetics. This makes your hot tub water murky and causes dirty scum lines. That's why we created an easy to use, fast acting enzyme cleaner and spa enzyme remover. Remove the gunk from your hot tub and keep it from coming back with our natural enzyme formula. Our natural enzyme cleaner help eliminate odors from your hot tub and prevents foul smells from coming back. Safely remove waterline stains and prevent future hot tub stains from forming. Our hot tub enzymes work to combat nonliving organic matter such as lotions and oils to break them down into smaller pieces that can be removed by your sanitizer. This product helps make your sanitizer chemicals more efficient and effective. l of AquaDoc's hot tub chemicals are professional grade formulas made in the USA. Directions for natural enzyme use:first, pour 1oz for every 250 gallons once daily until scum lines and foul odors are gone. To prevent future issues, use our natural spa enzyme formula regularly by adding 1oz per 250 gallons of water on a weekly basis. Only required once per week unless using the hot tub multiple times a day. Wait 15 minutes after use before entering hot tub after using the spa enzyme formula.