Prices, Promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.

Related Searches

Related Products

0.875-in Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.875-in Side/Top -Mount Sliding Closet Door Roller assembly

This is a top, center mounted, adjustable, tandem roller assembly. The 7/8 inch round edged or convex nylon rollers are attached to a stamped steel tandem housing and sits offset on top of a 5/16 inch threaded steel rod. The unique positioning of the rollers allow one roller to ride in one track while the other rides in the opposite track. Used on Acme series 2600, 1-3/8 inch thick closet. The horizontal roller located on the threaded rod can be adjusted up or down 5/8 inch by design and provides guidance as the roller assembly passes between the 2 opposite J-tracks.

1.5-in Bottom -Mount Sliding Closet Door Roller assembly

Prime-Line   1.5-in Bottom -Mount Sliding Closet Door Roller assembly

This has an adjustable steel housing with a 1-7/16 inch ball bearing roller. Used on Charmac mirrored doors in the late 1990's, the original designed housing is no longer available. In some cases, to make this part work the lower tab(s) may need to be trimmed off. Never remove the upper tabs nearest the adjusting screw. The housing upper tab snaps into a slot on the inside of the door frame, while the door rests on the bottom tabs that extend out from the base of the housing.

1.5-in Bottom -Mount Sliding Closet Door Roller assembly

Prime-Line   1.5-in Bottom -Mount Sliding Closet Door Roller assembly

This is an adjustable mirrored door assembly with a 1-1/2 in. concave nylon roller and used on Cox series 21 and 22 door systems. The unique design has bottom feet, or brackets, that fit under the door frame and are fastened into place there then up the side. The 1/1-2 in. nylon roller provides a smooth ride for heavy mirrored doors. May need to adjust if you notice any binding.

0.75-in Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.75-in Side/Top -Mount Sliding Closet Door Roller assembly

This by-pass closet door repair kit includes four roller assemblies constructed of stamped steel brackets and plastic wheels. One pair of roller assemblies is for installation on the front sliding panels and have only a 1/4 inch offset. The other pair is for the sliding closet door panel that hangs on the rear track. The roller assemblies of this second pair have 1/2 inch offsets. Each roller assembly features 3/4 inch diameter wheels. The wheels have convex (round) edges and all are top hung, side-mount design. These roller assemblies are used on Cox doors and on many others.

0.75-in Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.75-in Side/Top -Mount Sliding Closet Door Roller assembly

This is a side mounted, top hung, adjustable wardrobe door roller assembly with a single 3/4 inch flat nylon wheel for the back door panel. The stamped steel bracket assembly is adjustable and has a 3/4 inch offset. It fits 3/4 inch to 1-3/8 inch thick doors. Used on atlas closet door systems as well as a variety of other wardrobe door manufacturers. For other offsets see Prime-Line parts N 6626 or N 6627.

1.5-in Bottom -Mount Sliding Closet Door Roller assembly

Prime-Line   1.5-in Bottom -Mount Sliding Closet Door Roller assembly

This sliding mirror door roller is constructed from nylon. It comes affixed to an adjustable steel housing that is easy to install. This style roller is used by a variety of other mirror door manufacturers.

1.5-in Bottom -Mount Sliding Closet Door Roller assembly

Prime-Line   1.5-in Bottom -Mount Sliding Closet Door Roller assembly

This is a paneled mirror door roller assembly with a concave nylon roller. Used on Monarch Mirror Doors L-Series. The grooved ball bearing nylon roller provides a smooth ride as it slide back and forth. The concave nylon roller is 1-1/2 in. in diameter. Note that the adjusting screw is centered on the top of the housing and the tabs on either side will insert into slots on that side and will be held in place by the existing screws.

0.875-in Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.875-in Side/Top -Mount Sliding Closet Door Roller assembly

This is a heavy-duty top mounted, adjustable roller assembly for Pocket or bi-passing wardrobe doors. It has four 7/8 inch nylon rollers that ride astride an upside down T-track design. Used on doors up to 100 lbs., Used on Acme 1000 and 1700 series track systems. For 3/4 inch rollers see Prime-Line part N 7087

0.87-in Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.87-in Side/Top -Mount Sliding Closet Door Roller assembly

This is a front and back roller for wardrobe door. It has concave rollers. Used on older Kennaframe sliding closet or wardrobe doors.

0.75-in Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.75-in Side/Top -Mount Sliding Closet Door Roller assembly

This is a side mounted, top hung wardrobe roller assembly with a single 3/4 inch convex nylon wheel for the front sliding door. The stamped steel bracket assembly is adjustable and has an 1/4 inch offset. It is used on 3/4 inch to 1-3/8 inch thick doors and up to 50 lbs. maximum each. Used by Cox door systems as well as a variety of other wardrobe door manufacturers. For the back wardrobe door se Prime-Line part N 6509.

1.5-in Side/Top-Mount Sliding Closet Door Roller Assembly

Prime-Line   1.5-in Side/Top-Mount Sliding Closet Door Roller Assembly

This mirror door roller assembly is constructed of an extruded aluminum housing, and it comes in a milled aluminum finish. The housing measures 1-3/4 inch wide, it is 1/2 inch thick and 3 inch tall. This housing bracket also features a round extruded boss, and it is used by Monarch Door Company on their 500 series aluminum-framed doors. The wheel is constructed of durable plastic which provides for a smooth, long-lasting, quiet roll and it features steel ball bearings and a concave edge. This mirror door roller assembly mounts on the bottoms of sliding mirrored closet doors, it is adjustable once installed, and it is used by a variety of closet door manufacturers.

0.875-in Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.875-in Side/Top -Mount Sliding Closet Door Roller assembly

This by-pass closet door repair kit includes four tandem roller assemblies constructed of stamped steel brackets and plastic wheels. One pair of tandem roller assemblies is for installation on the front sliding panels and have only a 1/4 inch offset. The other pair is for the sliding closet door panel that hangs on the rear track. The roller assemblies of this second pair have 1/2 inch offsets. Each roller assembly features 7/8 inch diameter wheels. The wheels have convex (round) edges and all are top hung, side-mount design. These roller assemblies are used on Acme and Stanley doors, in addition to many others.

0.75-in Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.75-in Side/Top -Mount Sliding Closet Door Roller assembly

This is a side mount, top hung adjustable roller bracket with a 3/4 inch ball bearing convex nylon roller and 1/2 inch offset that fits onto the back wardrobe door panel. It fits 3/4 inch to 1-3/8 inch thick doors.

Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   Side/Top -Mount Sliding Closet Door Roller assembly

This is a top guide that fits on top of the Cox Series 21 Door Systems. The guides are handed left and right, and snap into the frame accordingly. You will want to use the Prime-Line part N 6817 roller assembly for the bottom of the door.

0.875-in Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.875-in Side/Top -Mount Sliding Closet Door Roller assembly

This is a side mounted, top hung, adjustable wardrobe door roller assembly with a single 7/8 inch grooved nylon wheel for the back door panel. The stamped steel bracket assembly is adjustable and has a 9/16 inch offset. It fits 3/4 inch to 1-3/8 inch thick doors. Used on old style Kenna-frame closet door systems. For the front door panel use Prime-Line part N 6717.

0.875-Inches Side/Top -Mount Sliding Closet Door Roller assembly

Prime-Line   0.875-Inches Side/Top -Mount Sliding Closet Door Roller assembly

This wardrobe door roller is constructed from nylon and comes affixed to a steel bracket. It features an offset adjustable top hung, side mount design. This style roller is used on Acme and similar styled bypass doors that are 3/4 inch to 1-3/8 inch thick.

1.5-in Bottom -Mount Sliding Closet Door Roller assembly

Prime-Line   1.5-in Bottom -Mount Sliding Closet Door Roller assembly

This mirror door roller assembly is constructed of a stamped steel housing and features a convex-edge plastic wheel. This roller is used on Cox series 21 and 22 door systems, and it mounts at the bottoms of the sliding mirror doors. It features a height adjustment design that ranges from its minimum collapsed height, to 1-5/8 inch in height. The wheel diameter measures 1-1/2 inch, and it's edge measures 1/8 inch wide. Installation fasteners are included with this mirror door roller assembly.

1.5-Inches Bottom -Mount Sliding Closet Door Roller assembly

Prime-Line   1.5-Inches Bottom -Mount Sliding Closet Door Roller assembly

This mirror door roller assembly is constructed of a steel housing and a concaved edge, plastic wheel. The housing has 3 inch mounting hole centers, it is 2-1/8 inch tall and 11/16 inch deep. This mirror door roller assembly is most commonly used on wood framed sliding mirror doors. The wheel is constructed of durable plastic which provides for a smooth, long-lasting, quiet roll and it features a narrow concave edge. This mirror door roller assembly mounts on the bottoms of sliding mirrored closet doors, it is adjustable once installed, and it is used by a variety of closet door manufacturers.

Closet Door Rollers to Help Doors Operate More Smoothly

Closet door rollers can help your sliding closet doors roll smoothly. When you install new bifold doors, you may need to purchase separate door rollers. Or you may want to replace old rollers because of damage or if the old rollers no longer function well. At Lowe’s, we carry closet door wheels in a variety of styles, sizes and materials.


Frequently Asked Questions


Q: How do you install sliding closet door rollers?

A: To install closet door rollers, check to see whether your closet doors have pre-installed roller brackets. If not, you can add them yourself. To do this, set up the roller track and brackets according to the manufacturer’s instructions. If you’re mounting a door that closes to the right, you’ll want to install the roller bracket on the upper right side of the door. You’ll do the opposite for a door that closes to the left. Take a look at our guide — How to Install Bifold Doors — for more detailed instructions regarding closet door installation.


Q: Why does my sliding door keep falling off?

A: Your sliding door may keep falling off because of damaged or dirty rollers. It could also be that the wheels and track are out of alignment. Check to make sure the wheels align properly with the track. If the wheels are dirty, clean them using a washcloth dipped in warm, soapy water.


Q: How do I make my closet door slide easily?

A: To make your closet door slide easily, clean the rollers and make sure they align properly with the track. Then, use a silicone lubricant on the rollers and tracks.