Welcome to Lowe's
Find a Store

Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.

Tomato-Cage Light Display

See how an ordinary tomato cage and strings of mini lights combine to make a brilliant work of art.

Tomato Cages

Project Overview

Skill Level


Estimated Time

A few hours

Estimated Cost


Tools and Materials


  • Electric drill
  • 3/16"and 3/32" drill bits
  • Pliers
  • Wire cutter
  • Hacksaw
  • Permanent felt-tip marker


  • 1 - 54" galvanized tomato cage (#159911)
  • 1 - 100' roll Anchor Wire galvanized steel wire; 4-strand, 20-gauge (#52687)
  • 1 roll The Hillman Group galvanized steel wire; 22-gauge (#62940)
  • 1 - 11-ounce Universal oil-rubbed bronze spray paint (#75474)
  • 8 medium screw eyes
  • 1 Severe Weather 4"x4" treated post cap (#7972)
  • 2 Gemmy white balls mini string lights (#330058)

Items may be Special Order in some stores. Product costs, availability, and item numbers may vary online or by market. Paint colors may vary slightly from those shown. Availability varies by market for lumber species and sizes.

Missing anything? Shop Online

Project Resources


Mount the Post Cap

Step 1

Remove the dowel screw from the post cap with pliers or cut it off with a hacksaw. Mark four equally spaced hole centers around the perimeter of the bottom of the post cap, 3/8" in from the edge. Drill 5/8"-deep holes to accept the tomato cage legs, angling them to match the taper of the tomato cage. (We used a 3/16" drill bit.)

Good to Know

All four holes must be the same depth for the post cap to sit level. To ensure uniformity, attach a masking tape "flag" to the drill bit to indicate the 5/8" drilling depth.

Step 2

Mark two equally spaced eye-screw pilot-hole centers between each pair of leg holes, 3/8" in from the edge of the post cap and drill the eight holes. (We used a 3/32" drill bit.) Drive in the screw eyes with pliers, aligning the eyes perpendicular to the edge of the post cap (like the minute dashes on a clock face). With the tomato cage upside down, insert the cage legs into the angled holes in the post cap.

Weave in Vertical Wires

Step 1

Measure the distance from the bottom cage ring to a screw eye. Double this measurement, add 6”, and cut eight pieces of 20-gauge, four-strand wire to this length. (We cut our wire 112" long.) Thread one piece of wire through a screw eye to the midpoint. Bend the wire at the midpoint and use pliers to tightly pinch it onto the screw eye.

Step 2

Starting at the top cage ring, wrap one leg of the 20-gauge wire once around the ring, pulling the wire snug. Proceed to the remaining rings, wrapping the wire once around the second and third rings and several times around the fourth (bottom) ring, pulling the wire snug at each ring. Run the wire straight from top to bottom. Cut the excess wire at the bottom ring. Repeat with the second leg of the 20-gauge wire. In turn, insert the remaining seven wires into the screw eyes, wrap them around the rings, and trim the excess wire.

Add Another Ring

Step 1

Mark the tomato-cage legs halfway between the post cap and the top ring with a permanent felt-tip marker. Make an additional ring by wrapping a piece of 20-gauge wire around the legs at the marks, cutting it so the ends overlap by 2". Cut four 11"-long ties from 22-gauge single-strand wire. Center the 20-gauge ring overlap on one cage leg at the mark and use one tie to bind the 20-gauge ring to the leg and wrap the overlapping ends together. Bind the 20-gauge ring to the other three legs at the marks with the remaining ties. When binding the ring to the cage legs, wrap the tie wire diagonally across the joint, alternating the direction one way and then the other to make wire bundles resembling little baskets.

Step 2

Cut eight more 11"-long, 22-gauge wire ties. Gather together each pair of vertical 20-gauge wires where they cross the just-completed 20-gauge wire ring and bind them to each other and the 20-gauge ring with the ties. Use the same alternating diagonal wrap as before.

Finishing Up

Step 1

For a decorative effect, cut 22 additional ties and bind the vertical 20-gauge wires to the tomato cage rings in a random pattern, using the alternating diagonal tie wrap.

Step 2

Then, spread newspaper, cardboard, or a drop cloth outdoors on the ground or driveway and spray paint the entire piece. (We used oil-rubbed bronze color paint.) With the paint dry, move the cage to the desired location, wrap with two strings of decorative lights, and plug them in.