Welcome to Lowe's
Find a Store

Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.

Tile a Backsplash without Toil

Tiling a backsplash just got easier by doing away with conventional adhesives.

Tile Backdrop

Project Overview

Skill Level


Estimated Time

1 day

Estimated Cost


Tools and Materials


  • Ruler or straightedge
  • Measuring tape
  • Utility knife or scissors
  • Rubber grout float
  • Sponge


  • White tiles (#64396)
  • MusselBound adhesive tile mat, 12-in x 15-ft rolls, #555605
  • White grout, #129567

Items may be Special Order in some stores. Product costs, availability, and item numbers may vary online or by market. Paint colors may vary slightly from those shown. Availability varies by market for lumber species and sizes.

Missing anything? Shop Online


Double-sided adhesive MusselBound mats replace mortar and bond instantly, letting you apply tile and grout the same day. Mats can be used with most types of individual tiles up to 12 inches square or mesh-backed mosaic sheets. Use the mats on clean, flat indoor surfaces such as backsplashes, countertops, and tub or shower walls. Avoid using them for floors, ceilings, fireplaces, steam rooms, shower floors, and surfaces that will be submerged in water. Mats don’t replace waterproofing products for tile.

Install the Adhesive Mats

Step 1

Turn off electricity to switches and outlets in the wall you plan to tile. Patch or level surfaces as needed, then clean the surface using a grease-cutting detergent or trisodium phosphate (TSP). Check for loose areas and finishes, such as peeling paint.

Step 2

Trim MusselBound mats to length

Measure the height of the area to be tiled and cut an adhesive mat to length using a knife and straightedge. (You can use scissors in a pinch.)

Good to Know

Plan to install strips vertically instead of one long horizontal piece.

Step 3

Apply strips to the wall

Peel the backing from the wall face of the first strip. Gently hold the strip against the wall and check that it’s plumb and level. If necessary, carefully lift the strip free of the wall to reposition it. Then lightly press the strip in place. Repeat for the remaining strips, but avoid overlaying the edges.

Good to Know

So long as the adhesive mats are pressed lightly in place, they can be repositioned. Pressing firmly creates the strong final bond. To understand the difference, cut a practice strip of adhesive and apply it to a smooth surface.

Step 4

Cut around outlets and switches

Carefully cut around outlet and switch boxes to remove portions of the adhesive mats covering them.

Step 5

Press adhesive against the wall

After all of the mats are in position, place a grout float against the mat and press for 5 seconds to anchor the mat and force out any bubbles and creases. Continue working along the mat until the entire surface is pressed in place.

Install the Tiles

Step 1

Before applying the tiles, use a sponge and mild detergent to remove dust from the back of each tile or tile sheet. Allow the tiles to dry before applying.

Step 2

Peel away the outside liner

Peel off the release liner one section at a time to expose the adhesive.

Step 3

Install tiles on adhesive sheets

Lay 1/8-inch-thick spacers on the counter or surface below the tile and lay the bottom course of tiles. If your tiles aren’t self-spacing, leave spaces of at least 1/8 inch around each tile. After the tiles are in place, use the grout float to press tiles against the adhesive as in Step 5 of the previous section.

Step 4

Grout must be applied within 24 hours of setting the tiles. Use a grout float at 45-degree angles to press grout between the tiles. Then clean the float and use it to squeegee excess grout off the tiles.

Step 5

As the grout film begins to form a haze on the tiles, lightly wipe the surface with a moist sponge. Clean the sponge frequently as you work, but avoid wiping away grout between the tiles.

Step 6

Allow the fresh grout to dry for at least 48 hours before applying a grout sealer.