Two Bags or Three?
Use our Mulch Calculator to estimate how much mulch you'll need for your landscaping projects.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Lay a Flagstone Walkway
Flagstone is an excellent choice for walkways because of its durability and maintenance-free characteristics. A flagstone walkway blends well with almost any type outdoor decor, from formal to rustic. Lowe's has the information you need to complete this project today.
Tools & Materials
Use this checklist when you go to the store and purchase your items.
Planning the Flagstone Walkway
A curved walk and flagstones of irregular shapes create a less formal look and feel, while a straight walk with squared corners and more regularly-shaped flagstones suggest formality. Here are two options when laying out a pathway:
- For a straight walk, lay out the perimeter of the planned pathway and drive a wooden stake into the ground at each corner.
- Use a pair of garden hoses to lay out a curved pathway. Adjust the bends and curves in the hoses to achieve a satisfactory design before staking out and digging the pathway.
Be careful when working with flagstones. Bend your knees and lift with your legs to avoid injury.
Laying the Walkway
Use a water level instead of a line level to set your guide strings for especially long runs (50' or more).
Step 1
On each stake, measure and mark a point 1/4" or so above the ground. This will be the ultimate height of the finished path. Tie a string between the stakes at the 1/4" mark, using a line level to keep the string level.
Step 2
To allow for water run-off, one end of your walkway will need to be 1/4" higher and slope away from the house. Raise the end of the string nearest the house to establish the correct slope ratio for the length of the pathway (1/4" to every foot of path).
Step 3
Adjust the line level of the string on the opposite uphill or downhill stake to ensure that both sides of the path are parallel.
Step 4
Do a rough layout with flagstones alongside the staked-out pathway.
Step 5
Install the edging.
Preparing the Foundation
Step 1
Dig up about 2 1/2" of the sod between the strings. If you choose to use the sod later, set it aside in a cool place and water.
Step 2
Dig up the soil so you have a constant depth of 2 1/2" from the base of your foundation to the string. Once it's dug, tamp it flat.
Step 3
Check again for the slope.
Step 4
Spread about 1 1/2" of sand over the freshly dug area. Distribute it evenly.
Step 5
To level the sand, take a 2x4 and smooth the surface with the edge. Tamp the sand over the entire foundation surface. Make sure you keep the necessary slope.
Laying the Flagstones
Although flagstones have rough, irregular surfaces, lay the pathway as evenly as possible to avoid trips and falls.
Step 1
Place the flagstones on top of the compacted sand.
Step 2
Adjust the height of each flagstone as necessary by adding or removing sand.
Step 3
To seat the flagstones, lay a straight 2x4 across them and tap along the board with a rubber mallet.
Step 4
After seating the flagstones, move the 2x4 across the surface of the flagstones to check for any unevenness.
Step 5
Gaps between the larger pieces of flagstones can be filled in with smaller, cut pieces.
Cutting and Shaping Flagstones
Cutting may be required to fit the curve of the walkway:
When trimming or cutting flagstones, wear heavy gloves, a long-sleeved shirt, and goggles to protect your eyes.
Step 1
Draw a cut line on the stone with a pencil.
Step 2
Tap the chisel along the cut line with a baby sledge hammer, making a series of cuts.
Step 3
Prop the flagstone so the cut line hangs over the edge of a piece of scrap 2x4 and position the chisel in the middle of the cut line.
Step 4
Strike the chisel sharply with the sledge hammer, breaking the flagstone along the groove.
Step 5
To shape the edges of a flagstone to fit into a gap, place the stone to be cut on top of the stones against which it will fit. Visualize the edges of the stones below and draw these shapes on the stone to be cut.
Step 6
Use the full blade of the chisel to chip away the edges of the stone to just inside the cut line, allowing for a gap between the stones.
Finishing
Step 1
Sprinkle a layer of sand over the entire pathway and sweep it into the gaps between the flagstones.
Step 2
Dampen the pathway with a light misting from a garden hose. Repeat the above process until all gaps are filled.
Step 3
The edges of the walkway can be finished with strips of sod tucked in and around the flagstones or by adding mulch.
Project Information
- Skill Level: Intermediate
*Time and Cost are estimated.