Get the Right Amount of Paint the First Time
Use our paint calculator to estimate how much paint to buy.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Man's best friend wants a home to be proud of, so throw him a bone and build him a great dog house. You can give your dog a haven from the weather that also matches your house. With these instructions, a beginner level do-it-yourselfer should be able to complete this project in a weekend, using common household tools.
Use this checklist when you go to the store and purchase your items.
Building an attractive and safe dog house doesn't have to be a complicated project. Just keep a few basic principles in mind:
The illustration provides the dimensions for the panel elements of our dog house. The house is designed to make the most use of a single sheet of plywood siding. Notice that the drawing has two floor panels-this is so you can double the thickness of the floor for rigidity.
Lay out the panels on the back of the siding as shown in the drawing. Then, carefully cut out the panels on the lines. Cut the entry hole only large enough to allow your dog easy access.
Cut your 10' 2x4 into the following:
These will be used to build the platform on which the house will be built.
Consult the drawing at right when performing the following steps:
Round the bottom of the 6" platform legs.
With tops aligned, nail the legs flush against the inside edges of the 22-7/8" long side pieces of the platform.
Assemble the frame by nailing the 20 3/4" front, back and side pieces in place as shown.
Note: The front and back pieces overlap the ends of the side pieces.
Finally, align the first floor panel with the frame. It should align without overhanging edges. This will assure that the frame is square and that it was properly assembled. If the floor and frame don't match up, double-check to make sure you have correctly assembled the frame. If the frame is assembled properly but there is a slight overhang in a place or two (perhaps because the panels weren't cut perfectly straight), trim off the excess with a circular saw. When all is well, nail both floor panels in place.
Rip the 8' 2x4 into 2x2 stock to be used as frame elements.
From these, cut 4 pieces 12 1/2" long.
Nail these pieces flush against the short edges of the sides. One frame piece should be positioned starting at the top of each side corner, leaving a 3 1/2" space at the bottom to allow the side panel to overhang the platform.
Also attach frame pieces to the inside roof line of the front and back panels. The frame pieces should meet at the top, and extend along the roof line to approximately 2 1/2" from the sides.
Put one of the sides in place (the edges of the side should align with the front and back of the platform) and nail it to the platform at the bottom. Repeat this step for the other side.
Now you may attach the back of the doghouse. Align it with the sides, and nail it in place, first against the platform, then into the 2"x 2" frame members in the corners. Do the same for the front.
Nail a 22" long piece of 2"x 2" flush against the top inside edge of one of the roof panels (along the 32" axis). The piece should be centered, 5" in from the edges of the panel. When both roof panels are installed, this piece will run across and support the ridge cap.
Place the first roof panel in position (the one with the frame piece along the top inside edge), and nail it to the frame attached to the top of the front and back of the doghouse. Be careful not to miss with the nails. You don't want to leave exposed nail points inside the doghouse. You may not be able to get inside once it is finished to take care of any problems.
Nail the remaining roof panel in place.
Shingles are an inexpensive and attractive way to prevent a doghouse from leaking. If you wish, you can shingle the dog's house to match your own. They are not hard to install, and a doghouse-unlike your own home-is forgiving of mistakes.
For a doghouse, using roofing felt is optional. If you have some lying around, or if you are just super conscientious and really, really love your dog, staple the paper to the roof in a single sheet running up one side and down the other. Be stingy with those staples though; you just need to hold the stuff in place until you can install the shingles.
Run the first row of shingles upside down (split tabs up) along the bottom of the roof edges. Use short roofing nails. Then, starting directly on top of this row, begin nailing the shingles in place in the pattern you desire. Cap the ridge with cut shingle tabs to prevent leaking. Take a look at your own roof. It will show you how it should look.
If you choose not to use shingles, form a cap from a piece of aluminum flashing to run along the joint where the two roof panels meet. Run two beads of roofing cement, or silicone caulk, along the bottom of the cap and nail it in place.
Round and sand any rough edges of the doghouse that could injure your dog. Some people prime and paint their doghouses to match their homes. Others treat the wood with linseed oil only, in case the dog tries to eat it. If you do paint your doghouse, use a good quality exterior latex house paint.
*Time and Cost are estimated.